1 Bi - Directional DC/AC Inverter Charger 5.0kVA, 9kW surge, Input 48VDC nominal Pure Sine wave output 50Hz+/-0.1%, THD 3%, 96% eff. 230V+/-2% Charger 70 - 140AMP DC @48V, c/w remote control and Battery temp sensor, 2 AC input, 187-265VAC Parallel and 3 Phase capable, 2 Relays, Communication Port (to be wired and configure phase 15kVA)Minimum Compliance Standards: Safety EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1. Each 3
2 Charge Controller (MPPT) Maximum Power Point Tracker type (MPPT) with a rated capacity of 5.8KW @ 48V deep cycle battery Gel or AGM configurable, flooded and Lithium compatible, complete with communication port, Parallel capable (for black start) (5000Wp connected) Minimum compliance Standards: Safety EN/IEC 62109-1, UL 1741, CSA C22.2. Minimum warranty: 5years Each 1
3 Remote control
C/W touch
Screen interface Communication and configuration remote control suitable for inverter and charge controller configuration (10-70V input, CAN-Bus, USB, Ethernet) must be internet compatible and have full inverter and
Charge controller integration Minimum Compliance Standards and certifications: Safety EN 60950-1: 2005, A1: 2009, A2: 2013 EMC EN 61000-6-3, EN 55014-1, EN 61000-6-2, EN 61000-6-1, EN 55014-2. Minimum warranty: 5years Each 1
4 PV Inverter
3phase 15.0KW, MP Tracker, Input 200 - 1000VDC nominal Pure Sine wave
Output 45-65Hz+/-0.1%, THD < 5%, 96% eff. 400V+/-2% c / w Wireless local Area Network and AC current sensor, AC output, Unit Parallel capability, USB RS422, RS 485 Communication Port. Minimum
Compliance standards: DIN V VDE 0126-1-1/A1, VDE AR N 4105, IEC 62109-1/-2, EIC 62116, EIC 61727 Each 1

Generation Equipment
5 Solar Modules 550Wp monocrystalline solar modules optimized to charge controller specifications (Aggregate capacity of 5.4kWp - for black start (10 Solar Modules PV's) + (15kWp for PV inverters. Minimum standards and certifications: ISO14001: 2004, OHSAS18001, IEC61215, IEC1730. Minimum Warranty: 10 Years with minimum rated power output of 80% after 20 years Each 40
6 Mounting
Hardware for

Energy storage equipment
7 Lithium Batteries A total Nominal system voltage of 48V, Sealed maintenance free deep cycle Lithium iron phosphate type complete with integrated battery bank management system. 3.5kWhr per module (total 51 kWh - 59.5kWhr energy storage equivalent @ 0.2C) Minimum compliance Standards: IEC 62619, CE, UN38.3, VDE. Minimum warranty: 10 years or 3000 full cycles Each 40
8 Battery bank
Mounting
Mounting and connecting hardware (battery rack) suitable for entire battery bank including manufacturer specific cable kits and all relevant accessories Lump sum 1

Installation and commissioning
9 Circuit breaker 125A 48V DC between inverter and battery bus bar (linked pair) or Unit Circuit Breaker equivalent Each 3
10 95mm2 red cable Multi strand pure copper cable from battery bank to inverter bus bar m 90
11 95mm2 black cable Multi strand pure copper cable from battery bank to inverter bus bar m 90
12 Copper Bus bar Box 600mmx900mm IP54 Bus bar box complete with 1 pair of 50mmx10mmx400mm copper bus bars on insulation stands Each 2
13 10mm2 Red Cable Multi strand pure copper cable from Charge Controller to PV Sub Array UV resistant m 400
14 10mm2 black Cable Multi strand pure copper cable from Charge Controller to PV Sub Array UV resistant m 400
15 PV combiner boxes IP54 PV box input complet e, up to 1000 VDC circuit breaker and surge protection devices (SPD) Each 6
16 Output dB CW/
Circuit Breake 60A AC/dB complete with residual current and SPD and isolation Each 1
17 Installation
Sundries Lugs, Nuts, bolts, Cable ties, grease, cable trays, screws Lump Sum 1
18 Perimeter
Fence Diamond mesh wire perimeter fence c/w with support poles and access control lockable gate (Wire to be approved by MOE) Lump Sum 1